A CLOSER LOOK
A little more about this product
ThinkGrow Model-I 480V for High-Voltage Commercial Rooms
Product details
- Large cultivation buildings usually bring in 480Y/277V three-phase service, and Canadian sites often run 600Y/347V.
- This version of the Model-I wires straight onto those circuits through an auto-sensing 347–480V driver.
- No step-down transformer sits between the panel and the lights.
- At that voltage it draws only 2.09A at 347V and 1.55A at 480V.
- On a 20A branch at the 80% continuous rule, that is ten fixtures per circuit at 480V.
- A 120V build using the standard Model-I would need a separate circuit for every two lights.
- Output is more than 1,829 µmol/s from 720W, an efficacy above 2.54 µmol/J.
- The single V-shaped bar measures 45.24 x 4.36 x 6.46 in, weighs 22.33 lbs and holds its driver inside.
- Coverage is 4 x 4 ft in flower and 5 x 5 ft in veg, hung more than 2.5 ft above canopy.
- Why 480V LED Grow Lights Pay Off in a Large Build
- Fewer amps per fixture means fewer home runs, smaller conductors and fewer breakers across a big flower room.
- That is where most of the savings land, in the electrical rough-in rather than on the monthly bill.
- The fixture itself behaves exactly like its lower-voltage twin once it is hung.
- White with some UV carries the crop, and a separate far-red channel handles end-of-day treatments late in flower.
- That channel stays idle until a TrolMaster Hydro-X with an LMA-T adapter is on the network.
- The slim bar casts little shadow, so it also suits greenhouses with high-voltage service.
- It needs that tall hang to spread evenly, which rules out tight vertical racks.
- The honest limit is the building itself.
- This driver will not run on household or 208–240V service at all.
- Rooms without high-voltage panels should choose the standard-voltage Model-I instead.
- Auto-Sensing 347-480V Driver: Connects to 480Y/277V or 600Y/347V building service with no step-down transformer.
- Low Amp Draw per Fixture: More fixtures per branch circuit means fewer home runs and smaller conductors across the room.
- Over 1,829 µmol/s at 2.54 µmol/J: Covers a 4x4 flowering canopy or a 5x5 veg area from one 720W bar.
- V-Shaped Bar with Built-In Driver: One slim fixture with nothing remote to mount, and very little shadow under greenhouse glass.
- UV in the White + Far-Red Channel: A sunlight-like base spectrum plus far red for end-of-day flowering treatments via Hydro-X.
- IP66 Housing: Rated for humid flower rooms, spray drift and washdown between crops.
- Technical Specifications
Specifications
- Model
- Model-I, 347-480V
- Input Power
- 720W
- PPF
- >1,829 µmol/s
- Spectrum
- Full spectrum with UV + separate far red channel
- Coverage
- Flower 4 x 4 ft / Veg 5 x 5 ft
- Input Voltage
- 347-480V auto-sensing
- Amperage
- 2.09A @ 347V / 1.55A @ 480V
- Power Factor
- ≥90%
- Mounting Height
- >2.5 ft above canopy
- Heat Output
- About 2,457 BTU/h
- Dimensions
- 45.24 x 4.36 x 6.46 in
- Weight
- 22.33 lbs
- Driver
- Built-in
- Low Amp Draw per Fixture
- More fixtures per branch circuit means fewer home runs and smaller conductors across the room.
- V-Shaped Bar with Built-In Driver
- One slim fixture with nothing remote to mount, and very little shadow under greenhouse glass.
Questions & discussion
Have a question or something useful to share? Start the conversation.