Büyümenin daha parlak bir yolu. Fabrikadan doğrudan toptan satış. 15 yılı aşkın süredir gelişen uzmanlık

Bu içerik şu anda orijinal dilinde mevcuttur.

Havalandırma ve İklimlendirmeToptan satış sorgusu

Quest Duct Kit (Q100)

Model / Ürün Kodu: 4042265

Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.

Kaynak referans fiyatıTRY 10,328.14

Sadece karşılaştırma amaçlıdır. Güncel toptan fiyatınızı, stok durumunu ve teslimat koşullarını talep edin.

Ödeme gerekmiyor. İhtiyaçlarınız hakkında bir görüşme.

Fabrikadan doğrudan destek15 yılı aşkın deneyim
DAHA YAKINDAN BAKALIM

Bu ürün hakkında biraz daha bilgi

Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.

Product details

  • What Is in the Quest 100 Duct Kit
  • Each one carries a round collar for duct, so the unit can draw from one space and deliver to another.
  • That is what lets a Quest 100 sit in a lung room, a hallway or a mechanical closet.
  • It still works the grow room through two runs of flex duct.
  • The filter stays in service.
  • The magnetic door closes over it, so a filter change is a pull and a push rather than a plenum removal.
  • Fitting it needs a portable drill, a T25 Torx driver and a 5/16 in hex driver, and nothing else.
  • The plenums hang on the cabinet's own panel screws.
  • Those screws back out halfway, the plenum's keyed slots drop over them, and the screws are tightened again.
  • The four fasteners then anchor the plenum tabs into the plastic base, self-drilling, with no pilot holes.
  • Quest's instructions open with the warning that matters: disconnect the dehumidifier from power before any of it starts.
  • The kit ships at about 5 lb.
  • Keep both runs as short and as straight as the room allows, and size them to the collars rather than necking down.
  • Back the two top panel screws and the two right panel screws out halfway, hang the plenum on them, and tighten.
  • Drive the two fasteners through the bottom tabs into the base.
  • Slide the filter in, arrow toward the machine, and close the magnetic door with the larger tab on top.
  • Then the supply side: four screws out halfway on the top, rear and left panels, plenum on, screws tight, two more fasteners into the base.
  • Seal the duct to each collar with foil tape rather than cloth tape.
  • A dehumidifier discharge is warm, and cloth adhesive lets go within a season.
  • Check the filter monthly once it is ducted.
  • Out of sight behind a door, a filter loads up faster than one on an open cabinet.
  • A loaded filter is the second reason a ducted unit underperforms.
  • Four self-drilling fasteners: Anchor the plenums to the base with no pilot holes.
  • Hangs on the panel screws: Keyed slots over half-backed screws, then tightened.
  • Three tools: Portable drill, T25 Torx driver, 5/16 in hex driver.
  • For the Quest 100: PN 4041870, and the 50 Hz PN 4046590.
  • Quest part 4042265: About 5 lb boxed.
  • Technical Specifications

Bunu projeniz için işe yarar hale getirelim.

Siparişinizde miktar, teslimat adresi, yetiştirme bölgesi ve varsa voltaj veya fiş gereksinimlerinizi belirtin. Özellikler, stok durumu, nakliye ve garanti koşulları yazılı teklifinizde teyit edilecektir.

Kaydedilen döviz kuru kullanılarak yapılan referans dönüşümü. 15 Kas 2026. Dönüştürülen tutarlar bir fiyat teklifi değildir.

BİRLİKTE BÜYÜYELİM

Sorular ve tartışma

0

Bir sorunuz mu var veya paylaşmak istediğiniz faydalı bir şey mi? Sohbeti başlatın.

KEŞFETMEYE DEVAM EDİN

Mekanınız için daha fazla olanak

Tüm ürünleri görüntüle
İYİ BİR ŞEYİN BAŞLANGICI

Projenizi gün ışığına çıkaralım.

İhtiyaçlarınız hakkında bize biraz bilgi verin. Verdiğiniz bilgiler doğrultusunda size uygun bir toptan satış teklifi hazırlayacağız.

Ürün listeniz

Ödeme yok. Yükümlülük yok. Sadece faydalı bir sohbet.