เนื้อหานี้มีให้บริการในภาษาต้นฉบับในขณะนี้
Netafim 16mm Insert Barb Tee - 100 Pack
รุ่น / รหัสสินค้า: 32500-011330
Laying out drip on a bench or a row bed means splitting lines, and the tee is the fitting that does it.
- Size
- 16 mm
- Fitting Type
- Barb tee, barb x barb x barb
- Dripline Inside Diameter
- 14.2 mm
- Dripline Wall Thickness
- 0.9 to 1.2 mm
สำหรับใช้เปรียบเทียบเท่านั้น กรุณาสอบถามราคาส่งปัจจุบัน ความพร้อมจำหน่าย และเงื่อนไขการจัดส่ง
ไม่ต้องจ่ายเงิน เพียงแค่พูดคุยเกี่ยวกับสิ่งที่คุณต้องการ
ข้อมูลเพิ่มเติมเกี่ยวกับผลิตภัณฑ์นี้
Laying out drip on a bench or a row bed means splitting lines, and the tee is the fitting that does it.
Product details
- Netafim 16mm Insert Barb Tee
- This one has three barbed ports in a T shape, all sized for 16 mm dripline.
- Water coming in one side carries straight through and also turns out the branch.
- That lets one feed line serve two beds, or a lateral start partway along a header.
- Netafim lists this tee for 16 mm dripline with an inside diameter of 14.2 mm.
- Its catalog fits it to heavy wall tubing with walls from 0.9 to 1.2 mm.
- Each barb grips the inside of the tube, so no clamps or glue are needed.
- The body is a UV and chemical resistant polymer that holds up to sun and fertilizer in the water.
- It is a single molded piece, so there are no joints inside the fitting to leak.
- Netafim's catalog number for this 100 bag is 32500-011330.
- One bag covers a large layout with tees to spare.
- Keeping spares on hand also makes it simple to add a bed later.
- Branching 16mm Dripline Without Leaks
- Plan the layout first so each tee lands where a branch is needed.
- Turn the water off and cut the run line square at the tee position.
- Push the two cut ends onto the straight-through ports of the tee.
- Then push the branch line onto the side port.
- Seat each tube fully over its barb so the joint does not pull off under pressure.
- A slight twist while pushing helps stiff tubing slide on.
- Warm cold tubing in the sun for a few minutes to soften it.
- Add up the emitter flow on both sides of the tee to check the feed line can carry it.
- Very long branches lose pressure toward the end, so keep runs within the dripline maker's length tables.
- Turn the zone on and check every port for drips at full pressure.
- Flush both legs with their ends open before closing them off.
- Mark tee positions on the layout plan so they are easy to find for future repairs.
- Three Barbed Ports: Splits one 16 mm line into two runs.
- Push-On Fit: No clamps, glue or tools.
- Heavy Wall Fit: For 14.2 mm ID dripline, 0.9 to 1.2 mm wall.
ข้อกำหนด
- Fitting Type
- Barb tee, barb x barb x barb
- Size
- 16 mm
- Dripline Inside Diameter
- 14.2 mm
- Dripline Wall Thickness
- 0.9 to 1.2 mm
- Material
- UV and chemical resistant polymer
- Pack Quantity
- 100
- Three Barbed Ports
- Splits one 16 mm line into two runs.
มาทำให้มันใช้งานได้กับโปรเจ็กต์ของคุณกันเถอะ
โปรดระบุจำนวนสินค้า สถานที่จัดส่ง พื้นที่เพาะปลูก และแรงดันไฟฟ้าหรือประเภทปลั๊กที่ต้องการในคำสอบถามของคุณ ข้อมูลจำเพาะ ความพร้อมจำหน่าย การจัดส่ง และเงื่อนไขการรับประกันจะได้รับการยืนยันในใบเสนอราคาที่เป็นลายลักษณ์อักษรของคุณ
การแปลงอ้างอิงโดยใช้อัตราแลกเปลี่ยนที่บันทึกไว้ ณ วันที่ 15 พ.ย. 2026. จำนวนเงินที่แปลงแล้วไม่ใช่ใบเสนอราคา
ความเป็นไปได้เพิ่มเติมสำหรับพื้นที่ของคุณ
Yield Lab 600W HPS+MH Cool Tube Hood Reflector Grow Light Kit
Yield Lab 600W HPS+MH Air Cool Tube Reflector Digital Grow Light Kit
คำถามและการอภิปราย
มีคำถามหรือสิ่งที่มีประโยชน์อยากแบ่งปันไหม? เริ่มการสนทนาได้เลย