เส้นทางการเติบโตที่สดใสกว่าเดิม ขายส่งตรงจากโรงงาน ประสบการณ์ที่สั่งสมมามากกว่า 15 ปี

เนื้อหานี้มีให้บริการในภาษาต้นฉบับในขณะนี้

Dilution Solutions Micro-Doser - Etatron eOne MF Micro Dosing Pump Panel

รุ่น / รหัสสินค้า: 709171

Dilution Solutions Micro-Doser Built on the Etatron eOne MF

Power supply
100 to 250 VAC, 50/60 Hz
Line size
3/4 in or 1.5 in (by variant)
Flow rate
1 L/h (0.26 GPH)
Maximum pressure
10 bar (145 PSI)
ราคาอ้างอิงแหล่งที่มาTHB 53,795.03

สำหรับใช้เปรียบเทียบเท่านั้น กรุณาสอบถามราคาส่งปัจจุบัน ความพร้อมจำหน่าย และเงื่อนไขการจัดส่ง

ไม่ต้องจ่ายเงิน เพียงแค่พูดคุยเกี่ยวกับสิ่งที่คุณต้องการ

การสนับสนุนโดยตรงจากโรงงานประสบการณ์มากกว่า 15 ปี
ดูรายละเอียดเพิ่มเติม

ข้อมูลเพิ่มเติมเกี่ยวกับผลิตภัณฑ์นี้

Dilution Solutions Micro-Doser Built on the Etatron eOne MF

Product details

  • The Micro-Doser is an assembled injection panel built around the Etatron eOne MF 0110, a microprocessor diaphragm pump made for proportional dosing.
  • A water meter on the panel reads flow in the main line, and the pump adds concentrate in step with it.
  • The pump delivers up to 1 L/h, about 0.26 GPH, against as much as 10 bar (145 PSI).
  • It runs up to 180 impulses per minute with an adjustable stroke, so the dose can sit at a fraction of a millilitre per gallon.
  • A backlit graphic display handles the programming.
  • The wetted path is built for concentrates, with a PVDF pump head, PTFE diaphragm, TFE/P seals and ceramic ball valves.
  • The panel arrives plumbed on polyethylene board with the meter, check valve, pressure relief valve, injection valve, unions and a mixing chamber.
  • Suction comes through a PVC tube with a foot filter, and separate PVC priming and polyethylene discharge tubes complete the kit.
  • The pump accepts a 100 to 250 VAC supply at 50/60 Hz.
  • Panels come in 3/4 in and 1.5 in line sizes, each in left-to-right or right-to-left flow.
  • A tank is not included, so plan a container for the concentrate.
  • Where a Micro Dosing Pump Fits in a Fertigation Room
  • Super-concentrated additives are the usual job, the bottles whose label rate sits below what a typical water-powered injector meters well.
  • Mount the panel on a wall close to the irrigation header, with the flow arrow matching the direction water travels.
  • That is why orientation matters, since each panel is plumbed for one flow direction across the wall.
  • Prime the pump through the priming tube before the first run, so no air sits in the head.
  • Keep the foot filter off the bottom of the concentrate tank, where sediment settles.
  • The pressure relief valve protects the line if a downstream valve closes while the pump is still stroking.
  • Flush the head and injection valve with clean water when switching products.
  • The honest limit is volume.
  • At about a litre an hour it is made for small, potent doses, not for base nutrients.
  • Heavy feed belongs on a larger injector, with this panel layered on top for the expensive bottle.
  • Etatron eOne MF 0110 Pump: A microprocessor diaphragm pump doses in proportion to the water meter reading.
  • 1 L/h at 10 bar: Output suits super-concentrated additives on a pressurized fertigation line.
  • Adjustable Stroke: Up to 180 impulses per minute with stroke control holds very low dose rates.
  • Chemical-Resistant Wetted Parts: PVDF head, PTFE diaphragm, TFE/P seals and ceramic balls handle concentrates.
  • Fully Plumbed Panel: Water meter, check, relief and injection valves, unions and a mixing chamber come assembled.
  • Two Sizes, Two Directions: Choose a 3/4 in or 1.5 in line size in left-to-right or right-to-left flow.

ข้อกำหนด

Flow rate
1 L/h (0.26 GPH)
Maximum pressure
10 bar (145 PSI)
Dosing frequency
Up to 180 impulses per minute
Power supply
100 to 250 VAC, 50/60 Hz
Line size
3/4 in or 1.5 in (by variant)
Flow direction
Left to right or right to left (by variant)
Option
0.75 in - (Left to Right), 0.75 in - (Right to Left), 1.5 in - (Right to Left), 1.5 in - (Left to Right)

มาทำให้มันใช้งานได้กับโปรเจ็กต์ของคุณกันเถอะ

โปรดระบุจำนวนสินค้า สถานที่จัดส่ง พื้นที่เพาะปลูก และแรงดันไฟฟ้าหรือประเภทปลั๊กที่ต้องการในคำสอบถามของคุณ ข้อมูลจำเพาะ ความพร้อมจำหน่าย การจัดส่ง และเงื่อนไขการรับประกันจะได้รับการยืนยันในใบเสนอราคาที่เป็นลายลักษณ์อักษรของคุณ

การแปลงอ้างอิงโดยใช้อัตราแลกเปลี่ยนที่บันทึกไว้ ณ วันที่ 15 พ.ย. 2026. จำนวนเงินที่แปลงแล้วไม่ใช่ใบเสนอราคา

เรามาเติบโตไปด้วยกัน

คำถามและการอภิปราย

0

มีคำถามหรือสิ่งที่มีประโยชน์อยากแบ่งปันไหม? เริ่มการสนทนาได้เลย

สำรวจต่อไป

ความเป็นไปได้เพิ่มเติมสำหรับพื้นที่ของคุณ

ดูสินค้าทั้งหมด
Yield Lab Air Cool Tube Reflector
ระบบไฮโดรโปนิกส์และการชลประทาน

Yield Lab Air Cool Tube Reflector

แหล่งอ้างอิงTHB 3,386.44
Yield Lab Air Cool Tube Hood Reflector
ระบบไฮโดรโปนิกส์และการชลประทาน

Yield Lab Air Cool Tube Hood Reflector

แหล่งอ้างอิงTHB 3,725.25
จุดเริ่มต้นของสิ่งที่ดี

มาทำให้โครงการของคุณเป็นจริงกันเถอะ

โปรดบอกรายละเอียดเกี่ยวกับสิ่งที่คุณต้องการ เราจะใช้ข้อมูลของคุณเพื่อเตรียมข้อเสนอราคาส่งที่เหมาะสม

รายการสินค้าของคุณ

ไม่ต้องจ่ายเงิน ไม่มีข้อผูกมัด แค่เป็นการสนทนาที่เป็นประโยชน์