Uma forma mais inteligente de crescer. Venda por atacado direto da fábrica. Mais de 15 anos de crescente experiência

Este conteúdo está disponível atualmente em seu idioma original.

Hidroponia e IrrigaçãoConsulta de atacado

Dilution Solutions Micro-Doser - Etatron eOne MF Micro Dosing Pump Panel

Modelo / SKU: 709171

Dilution Solutions Micro-Doser Built on the Etatron eOne MF

Power supply
100 to 250 VAC, 50/60 Hz
Line size
3/4 in or 1.5 in (by variant)
Flow rate
1 L/h (0.26 GPH)
Maximum pressure
10 bar (145 PSI)
Preço de referência da fonteEUR 1,438.48

Apenas para fins de comparação. Solicite seu preço de atacado atual, disponibilidade e condições de entrega.

Nenhum pagamento é necessário. Uma conversa sobre o que você precisa.

Suporte direto da fábricaMais de 15 anos de experiência
UMA ANÁLISE MAIS DETALHADA

Um pouco mais sobre este produto

Dilution Solutions Micro-Doser Built on the Etatron eOne MF

Product details

  • The Micro-Doser is an assembled injection panel built around the Etatron eOne MF 0110, a microprocessor diaphragm pump made for proportional dosing.
  • A water meter on the panel reads flow in the main line, and the pump adds concentrate in step with it.
  • The pump delivers up to 1 L/h, about 0.26 GPH, against as much as 10 bar (145 PSI).
  • It runs up to 180 impulses per minute with an adjustable stroke, so the dose can sit at a fraction of a millilitre per gallon.
  • A backlit graphic display handles the programming.
  • The wetted path is built for concentrates, with a PVDF pump head, PTFE diaphragm, TFE/P seals and ceramic ball valves.
  • The panel arrives plumbed on polyethylene board with the meter, check valve, pressure relief valve, injection valve, unions and a mixing chamber.
  • Suction comes through a PVC tube with a foot filter, and separate PVC priming and polyethylene discharge tubes complete the kit.
  • The pump accepts a 100 to 250 VAC supply at 50/60 Hz.
  • Panels come in 3/4 in and 1.5 in line sizes, each in left-to-right or right-to-left flow.
  • A tank is not included, so plan a container for the concentrate.
  • Where a Micro Dosing Pump Fits in a Fertigation Room
  • Super-concentrated additives are the usual job, the bottles whose label rate sits below what a typical water-powered injector meters well.
  • Mount the panel on a wall close to the irrigation header, with the flow arrow matching the direction water travels.
  • That is why orientation matters, since each panel is plumbed for one flow direction across the wall.
  • Prime the pump through the priming tube before the first run, so no air sits in the head.
  • Keep the foot filter off the bottom of the concentrate tank, where sediment settles.
  • The pressure relief valve protects the line if a downstream valve closes while the pump is still stroking.
  • Flush the head and injection valve with clean water when switching products.
  • The honest limit is volume.
  • At about a litre an hour it is made for small, potent doses, not for base nutrients.
  • Heavy feed belongs on a larger injector, with this panel layered on top for the expensive bottle.
  • Etatron eOne MF 0110 Pump: A microprocessor diaphragm pump doses in proportion to the water meter reading.
  • 1 L/h at 10 bar: Output suits super-concentrated additives on a pressurized fertigation line.
  • Adjustable Stroke: Up to 180 impulses per minute with stroke control holds very low dose rates.
  • Chemical-Resistant Wetted Parts: PVDF head, PTFE diaphragm, TFE/P seals and ceramic balls handle concentrates.
  • Fully Plumbed Panel: Water meter, check, relief and injection valves, unions and a mixing chamber come assembled.
  • Two Sizes, Two Directions: Choose a 3/4 in or 1.5 in line size in left-to-right or right-to-left flow.

Especificações

Flow rate
1 L/h (0.26 GPH)
Maximum pressure
10 bar (145 PSI)
Dosing frequency
Up to 180 impulses per minute
Power supply
100 to 250 VAC, 50/60 Hz
Line size
3/4 in or 1.5 in (by variant)
Flow direction
Left to right or right to left (by variant)
Option
0.75 in - (Left to Right), 0.75 in - (Right to Left), 1.5 in - (Right to Left), 1.5 in - (Left to Right)

Vamos fazer isso funcionar para o seu projeto.

Inclua a quantidade desejada, o local de entrega, a região de cultivo e quaisquer requisitos de voltagem ou tipo de plugue em sua solicitação. As especificações, a disponibilidade, os termos de envio e a garantia serão confirmados em seu orçamento por escrito.

Conversão de referência usando a taxa de câmbio salva com a data 15 de nov. de 2026. Os valores convertidos não constituem uma cotação.

VAMOS CRESCER JUNTOS

Perguntas e discussão

0

Tem alguma pergunta ou algo útil para compartilhar? Inicie a conversa.

CONTINUE EXPLORANDO

Mais possibilidades para o seu espaço

Ver todos os produtos
O INÍCIO DE ALGO BOM

Vamos dar visibilidade ao seu projeto.

Conte-nos um pouco sobre suas necessidades. Usaremos suas informações para preparar uma proposta de atacado adequada.

Sua lista de produtos

Sem pagamento. Sem compromisso. Apenas uma conversa útil.