Ventilation & ClimateWholesale inquiry
Quest Duct Kit (Q100)
Model / SKU: 4042265
Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.
Source reference priceUSD 205.00
For comparison only. Request your current wholesale price, availability and delivery terms.
No payment required. A conversation about what you need.
Factory-direct support15+ years of experience
A CLOSER LOOK
A little more about this product
Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.
Product details
- What Is in the Quest 100 Duct Kit
- Each one carries a round collar for duct, so the unit can draw from one space and deliver to another.
- That is what lets a Quest 100 sit in a lung room, a hallway or a mechanical closet.
- It still works the grow room through two runs of flex duct.
- The filter stays in service.
- The magnetic door closes over it, so a filter change is a pull and a push rather than a plenum removal.
- Fitting it needs a portable drill, a T25 Torx driver and a 5/16 in hex driver, and nothing else.
- The plenums hang on the cabinet's own panel screws.
- Those screws back out halfway, the plenum's keyed slots drop over them, and the screws are tightened again.
- The four fasteners then anchor the plenum tabs into the plastic base, self-drilling, with no pilot holes.
- Quest's instructions open with the warning that matters: disconnect the dehumidifier from power before any of it starts.
- The kit ships at about 5 lb.
- Keep both runs as short and as straight as the room allows, and size them to the collars rather than necking down.
- Back the two top panel screws and the two right panel screws out halfway, hang the plenum on them, and tighten.
- Drive the two fasteners through the bottom tabs into the base.
- Slide the filter in, arrow toward the machine, and close the magnetic door with the larger tab on top.
- Then the supply side: four screws out halfway on the top, rear and left panels, plenum on, screws tight, two more fasteners into the base.
- Seal the duct to each collar with foil tape rather than cloth tape.
- A dehumidifier discharge is warm, and cloth adhesive lets go within a season.
- Check the filter monthly once it is ducted.
- Out of sight behind a door, a filter loads up faster than one on an open cabinet.
- A loaded filter is the second reason a ducted unit underperforms.
- Four self-drilling fasteners: Anchor the plenums to the base with no pilot holes.
- Hangs on the panel screws: Keyed slots over half-backed screws, then tightened.
- Three tools: Portable drill, T25 Torx driver, 5/16 in hex driver.
- For the Quest 100: PN 4041870, and the 50 Hz PN 4046590.
- Quest part 4042265: About 5 lb boxed.
- Technical Specifications
Let’s make it work for your project
Include your quantity, delivery destination, growing area and any voltage or plug requirements in your inquiry. Specifications, availability, shipping and warranty terms are confirmed in your written quotation.
KEEP EXPLORING
View all productsMore possibilities for your space
Ventilation & Climate
Yield Lab 6 Inch Purifier Activated Charcoal Filter
Source referenceUSD 149.95
Ventilation & Climate
Yield Lab 6 inch 440 CFM Duct Inline Fan with 6" Carbon Filter Ducting and Clamps
Source referenceUSD 139.95
Ventilation & Climate
Yield Lab 6 Inch 440 CFM Charcoal Filter and Duct Fan Combo Kit
Source referenceUSD 119.95
Questions & discussion
Have a question or something useful to share? Start the conversation.