Hydroponics & IrrigationWholesale inquiry
Netafim Pressure Regulating Unit 65 psi Replacement Module for High Flow Regulators
Model / SKU: 31500-002000
Netafim Pressure Regulating Unit 65 psi
- Type
- Sealed pressure regulating unit (replacement module)
- Preset Outlet Pressure
- 65 psi
- Housing Flow Ranges
- 3/4 in high flow: 4.5 to 17.5 GPM; 1 1/2 in: 11 to 35 GPM
- Regulator Max Operating Pressure
- 145 psi
Source reference priceUSD 9.85
For comparison only. Request your current wholesale price, availability and delivery terms.
No payment required. A conversation about what you need.
Factory-direct support15+ years of experience
A CLOSER LOOK
A little more about this product
Netafim Pressure Regulating Unit 65 psi
Product details
- Some irrigation layouts need a higher working pressure than drip lines, and the regulator still has to cap it at a steady number.
- This sealed module sets that cap at 65 psi.
- It is the top preset in the standard Netafim range, which starts at 9 psi.
- Each pressure in that range uses its own one-piece unit.
- This one has no adjustment, so the setpoint will not wander over time.
- In the 3/4 inch high flow regulator it works as the single module.
- The 1 1/2 inch regulator takes two of them side by side.
- The 2 inch regulator holds four.
- The regulator line uses a stainless steel spring against an EPDM rubber diaphragm.
- Its bodies are non-corrosive plastic and brass.
- Netafim rates the line for operating pressures up to 145 psi, leaving room above this setpoint.
- Use it on zones whose sprinklers or emitters are specified for a 65 psi supply.
- Fitting a 65 psi Regulator Module
- Isolate the regulator by closing the upstream valve.
- Drain or bleed the pressure in the line before opening anything.
- Open the housing following the Netafim directions for that regulator size.
- Remove the old module and inspect the seat and seals.
- Clean out any grit, then fit the new unit in the same orientation.
- In dual and four module regulators, load matching modules in every slot.
- Close the housing and snug it by hand.
- Reopen the supply slowly to let the diaphragm settle.
- Confirm the outlet reading on a downstream gauge.
- Fit a filter ahead of the regulator to keep debris off the module.
- Recheck outlet pressure at the start of each season.
- 65 psi Preset: Top setting in the standard Netafim range.
- Sealed Module: One-piece unit with a fixed setpoint.
- Fits Three Housings: 3/4 in high flow, 1 1/2 in dual and 2 in four module regulators.
- Field Replaceable: Renews a regulator without cutting pipe.
Specifications
- Type
- Sealed pressure regulating unit (replacement module)
- Preset Outlet Pressure
- 65 psi
- Housing Flow Ranges
- 3/4 in high flow: 4.5 to 17.5 GPM; 1 1/2 in: 11 to 35 GPM
- Regulator Max Operating Pressure
- 145 psi
- Regulator Materials
- Plastic and brass body, stainless steel spring, EPDM diaphragm
- Sealed Module
- One-piece unit with a fixed setpoint.
Let’s make it work for your project
Include your quantity, delivery destination, growing area and any voltage or plug requirements in your inquiry. Specifications, availability, shipping and warranty terms are confirmed in your written quotation.
KEEP EXPLORING
View all productsMore possibilities for your space
Hydroponics & Irrigation
Yield Lab 600W HPS+MH Cool Tube Hood Reflector Grow Light Kit
Source referenceUSD 219.95
Hydroponics & Irrigation
Yield Lab 600W HPS+MH Air Cool Tube Reflector Digital Grow Light Kit
Source referenceUSD 199.95
Hydroponics & Irrigation
Yield Lab 600w HPS Air Cool Tube Digital Dimming Grow Light Kit
Source referenceUSD 189.95
Questions & discussion
Have a question or something useful to share? Start the conversation.