Jaśniejszy sposób na rozwój. Sprzedaż hurtowa bezpośrednio z fabryki. Ponad 15 lat rosnącego doświadczenia

Ta treść jest obecnie dostępna w oryginalnym języku.

ThunderVak Replacement Blades

Model / SKU: 777877

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Type
Replacement cutting wires
Material
Nylon
Cena referencyjna źródłaPLN 34.53

Tylko do celów porównawczych. Zapytaj o aktualną cenę hurtową, dostępność i warunki dostawy.

Brak opłat. Rozmowa o tym, czego potrzebujesz.

Wsparcie bezpośrednio od producentaPonad 15 lat doświadczenia
BLIŻSZE SPOJRZENIE

Trochę więcej o tym produkcie

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Product details

  • The ThunderVak trims with spinning nylon cords rather than steel knives, and these are the cords it uses.
  • Each wire is a length of round blue nylon with a crimped metal grommet on one end.
  • The grommet seats in the cutting spool on top of the base motor, so the wire stays put at full speed.
  • Fanned out around the spool, the wires sweep just under the aluminum grill.
  • Leaf that hangs through the grill gets clipped while the flower rides above it.
  • The machine runs 8 cutting wires at a time.
  • Nylon cuts cleanly without needing to be sharpened, and a worn wire is swapped for a fresh one.
  • Round blue wires are one of the two styles the trimmer accepts, alongside the octagonal red set.
  • Growers keep a spare set on the shelf so a nicked or shortened cord never stops a harvest.
  • The wires fit the ThunderVak Composter Plus leaf trimmer.
  • As a wear part, a fresh set is the quickest fix for an uneven cut.
  • Swapping Nylon Cutting Wires Between Batches
  • Turn both motors off and unplug the trimmer before touching the cutting area.
  • Lift off the upper reservoir and the grill to expose the spool.
  • Look over every wire for frayed ends, flat spots or missing length.
  • Slide a damaged wire out of its hole in the spool and throw it away.
  • Push a new wire in until its metal grommet seats firmly.
  • Repeat around the spool so the full set is fresh and even.
  • Matching lengths keep the cut level and the motor running smoothly.
  • Set the grill back on and make sure it sits flat on the motor support.
  • The trimming height is preset at the factory, so no adjustment is usually needed after a swap.
  • Run a small handful of material first to confirm the finish looks right.
  • Clean the cutting area after each session with a mild natural cleaner and a damp cloth.
  • Skip abrasive pads, which scratch the surfaces around the spool.
  • Store spare wires flat in a dry bag so they stay straight.
  • Checking the set before every run keeps the trim consistent from first batch to last.
  • Nylon Cutting Cord: Round blue nylon trims leaf cleanly and never needs sharpening.
  • Metal Grommet End: A crimped fitting locks each wire into the cutting spool at speed.

Specyfikacje

Type
Replacement cutting wires
Material
Nylon

Sprawmy, żeby to zadziałało w Twoim projekcie

W zapytaniu ofertowym prosimy o podanie ilości, miejsca dostawy, obszaru uprawy oraz wszelkich wymagań dotyczących napięcia lub wtyczki. Specyfikacja, dostępność, warunki wysyłki i gwarancji zostaną potwierdzone w pisemnej ofercie.

Przeliczenie referencyjne przy użyciu zapisanego kursu wymiany z dnia 15 lis 2026. Przeliczone kwoty nie stanowią oferty handlowej.

ROŚNIJMY RAZEM

Pytania i dyskusja

0

Masz pytanie lub chcesz się czymś podzielić? Rozpocznij rozmowę.

KONTYNUUJ ODKRYWANIE

Więcej możliwości dla Twojej przestrzeni

Zobacz wszystkie produkty
POCZĄTEK CZEGOŚ DOBREGO

Rzućmy światło na Twój projekt.

Powiedz nam trochę o swoich potrzebach. Wykorzystamy Twoje dane, aby przygotować odpowiednią odpowiedź hurtową.

Twoja lista produktów

Bez opłat. Bez zobowiązań. Tylko pomocna rozmowa.