Ta treść jest obecnie dostępna w oryginalnym języku.
Akcesoria oświetlenioweZapytanie hurtowe
Sero Bus Cable, 3 ft
Model / SKU: 705140
Sero 3 ft Bus Cable for Modules on One Wall
- Type
- System bus cable
- Length
- 3 ft
- Compatibility
- Sero System
Cena referencyjna źródłaPLN 47.19
Tylko do celów porównawczych. Zapytaj o aktualną cenę hurtową, dostępność i warunki dostawy.
Brak opłat. Rozmowa o tym, czego potrzebujesz.
Wsparcie bezpośrednio od producentaPonad 15 lat doświadczenia
BLIŻSZE SPOJRZENIE
Trochę więcej o tym produkcie
Sero 3 ft Bus Cable for Modules on One Wall
Product details
- Control gear rarely mounts in one row.
- A sensor module may sit above the controller, or a relay unit may hang a short way down the wall.
- This Sero cable covers those small gaps at 3 feet long.
- It reaches from one component to the next without leaving a large loop behind.
- That makes it a good fit for a single equipment board or a compact cabinet.
- That length gives some room to route around a bracket or conduit.
- Sero states that only its approved bus cables should connect system components.
- A matched cable keeps the system bus working the way it was designed.
- Each cable joins one unit to the next in the chain.
- Count the gaps between components to work out how many are needed.
- Measure along the planned route, not in a straight line, before choosing a length.
- Routing a Controller Cable Between Units
- Shut off power to the system before connecting or disconnecting any bus cable.
- Lay out the route so the cable follows walls, rails or cable trays.
- Fasten it every so often with soft ties, snug but not tight enough to pinch.
- Leave a small service loop near each connector so the plug never pulls taut.
- Push each connector home until it seats, then check that it stays put.
- Keep the cable away from heaters, ballasts and other hot equipment.
- Separate it from mains power lines where possible.
- Label both ends so the right module is easy to find later.
- Power the system back up and confirm each component reports to the controller.
- Check the run periodically for chafing where it crosses an edge.
- Swap out any cable with a damaged jacket or loose plug.
- 3 ft Length: Spans units on one wall or cabinet.
- Routing Room: Reaches around brackets and conduit.
- Sero Approved: Matched to Sero System components.
- One Link per Gap: Connects one unit to the next.
- Tidy Install: Little spare cable to coil.
Specyfikacje
- Type
- System bus cable
- Length
- 3 ft
- Compatibility
- Sero System
Sprawmy, żeby to zadziałało w Twoim projekcie
W zapytaniu ofertowym prosimy o podanie ilości, miejsca dostawy, obszaru uprawy oraz wszelkich wymagań dotyczących napięcia lub wtyczki. Specyfikacja, dostępność, warunki wysyłki i gwarancji zostaną potwierdzone w pisemnej ofercie.
Przeliczenie referencyjne przy użyciu zapisanego kursu wymiany z dnia 15 lis 2026. Przeliczone kwoty nie stanowią oferty handlowej.
KONTYNUUJ ODKRYWANIE
Zobacz wszystkie produktyWięcej możliwości dla Twojej przestrzeni
Akcesoria oświetleniowe
Yield Lab Professional Series Double Ended Grow Light Reflector
Odniesienie do źródłaPLN 259.26
Akcesoria oświetleniowe
Yield Lab Professional Series 120/220v 630w Dual Bulb CMH Open Wing Reflector/Ballast
Odniesienie do źródłaPLN 1,193.71
Akcesoria oświetleniowe
Yield Lab Pro Series 120/220V 1000W Double Ended Complete Grow Light Kit
Odniesienie do źródłaPLN 598.65
Pytania i dyskusja
Masz pytanie lub chcesz się czymś podzielić? Rozpocznij rozmowę.