Jaśniejszy sposób na rozwój. Sprzedaż hurtowa bezpośrednio z fabryki. Ponad 15 lat rosnącego doświadczenia

Ta treść jest obecnie dostępna w oryginalnym języku.

Wentylacja i klimatZapytanie hurtowe

Quest Duct Kit (Q100)

Model / SKU: 4042265

Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.

Cena referencyjna źródłaPLN 818.43

Tylko do celów porównawczych. Zapytaj o aktualną cenę hurtową, dostępność i warunki dostawy.

Brak opłat. Rozmowa o tym, czego potrzebujesz.

Wsparcie bezpośrednio od producentaPonad 15 lat doświadczenia
BLIŻSZE SPOJRZENIE

Trochę więcej o tym produkcie

Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.

Product details

  • What Is in the Quest 100 Duct Kit
  • Each one carries a round collar for duct, so the unit can draw from one space and deliver to another.
  • That is what lets a Quest 100 sit in a lung room, a hallway or a mechanical closet.
  • It still works the grow room through two runs of flex duct.
  • The filter stays in service.
  • The magnetic door closes over it, so a filter change is a pull and a push rather than a plenum removal.
  • Fitting it needs a portable drill, a T25 Torx driver and a 5/16 in hex driver, and nothing else.
  • The plenums hang on the cabinet's own panel screws.
  • Those screws back out halfway, the plenum's keyed slots drop over them, and the screws are tightened again.
  • The four fasteners then anchor the plenum tabs into the plastic base, self-drilling, with no pilot holes.
  • Quest's instructions open with the warning that matters: disconnect the dehumidifier from power before any of it starts.
  • The kit ships at about 5 lb.
  • Keep both runs as short and as straight as the room allows, and size them to the collars rather than necking down.
  • Back the two top panel screws and the two right panel screws out halfway, hang the plenum on them, and tighten.
  • Drive the two fasteners through the bottom tabs into the base.
  • Slide the filter in, arrow toward the machine, and close the magnetic door with the larger tab on top.
  • Then the supply side: four screws out halfway on the top, rear and left panels, plenum on, screws tight, two more fasteners into the base.
  • Seal the duct to each collar with foil tape rather than cloth tape.
  • A dehumidifier discharge is warm, and cloth adhesive lets go within a season.
  • Check the filter monthly once it is ducted.
  • Out of sight behind a door, a filter loads up faster than one on an open cabinet.
  • A loaded filter is the second reason a ducted unit underperforms.
  • Four self-drilling fasteners: Anchor the plenums to the base with no pilot holes.
  • Hangs on the panel screws: Keyed slots over half-backed screws, then tightened.
  • Three tools: Portable drill, T25 Torx driver, 5/16 in hex driver.
  • For the Quest 100: PN 4041870, and the 50 Hz PN 4046590.
  • Quest part 4042265: About 5 lb boxed.
  • Technical Specifications

Sprawmy, żeby to zadziałało w Twoim projekcie

W zapytaniu ofertowym prosimy o podanie ilości, miejsca dostawy, obszaru uprawy oraz wszelkich wymagań dotyczących napięcia lub wtyczki. Specyfikacja, dostępność, warunki wysyłki i gwarancji zostaną potwierdzone w pisemnej ofercie.

Przeliczenie referencyjne przy użyciu zapisanego kursu wymiany z dnia 15 lis 2026. Przeliczone kwoty nie stanowią oferty handlowej.

ROŚNIJMY RAZEM

Pytania i dyskusja

0

Masz pytanie lub chcesz się czymś podzielić? Rozpocznij rozmowę.

KONTYNUUJ ODKRYWANIE

Więcej możliwości dla Twojej przestrzeni

Zobacz wszystkie produkty
POCZĄTEK CZEGOŚ DOBREGO

Rzućmy światło na Twój projekt.

Powiedz nam trochę o swoich potrzebach. Wykorzystamy Twoje dane, aby przygotować odpowiednią odpowiedź hurtową.

Twoja lista produktów

Bez opłat. Bez zobowiązań. Tylko pomocna rozmowa.