Jaśniejszy sposób na rozwój. Sprzedaż hurtowa bezpośrednio z fabryki. Ponad 15 lat rosnącego doświadczenia

Ta treść jest obecnie dostępna w oryginalnym języku.

Hydroponika i nawadnianieZapytanie hurtowe

Netafim 16mm Insert Barb Tee - 100 Pack

Model / SKU: 32500-011330

Laying out drip on a bench or a row bed means splitting lines, and the tee is the fitting that does it.

Size
16 mm
Fitting Type
Barb tee, barb x barb x barb
Dripline Inside Diameter
14.2 mm
Dripline Wall Thickness
0.9 to 1.2 mm
Cena referencyjna źródłaPLN 297.27

Tylko do celów porównawczych. Zapytaj o aktualną cenę hurtową, dostępność i warunki dostawy.

Brak opłat. Rozmowa o tym, czego potrzebujesz.

Wsparcie bezpośrednio od producentaPonad 15 lat doświadczenia
BLIŻSZE SPOJRZENIE

Trochę więcej o tym produkcie

Laying out drip on a bench or a row bed means splitting lines, and the tee is the fitting that does it.

Product details

  • Netafim 16mm Insert Barb Tee
  • This one has three barbed ports in a T shape, all sized for 16 mm dripline.
  • Water coming in one side carries straight through and also turns out the branch.
  • That lets one feed line serve two beds, or a lateral start partway along a header.
  • Netafim lists this tee for 16 mm dripline with an inside diameter of 14.2 mm.
  • Its catalog fits it to heavy wall tubing with walls from 0.9 to 1.2 mm.
  • Each barb grips the inside of the tube, so no clamps or glue are needed.
  • The body is a UV and chemical resistant polymer that holds up to sun and fertilizer in the water.
  • It is a single molded piece, so there are no joints inside the fitting to leak.
  • Netafim's catalog number for this 100 bag is 32500-011330.
  • One bag covers a large layout with tees to spare.
  • Keeping spares on hand also makes it simple to add a bed later.
  • Branching 16mm Dripline Without Leaks
  • Plan the layout first so each tee lands where a branch is needed.
  • Turn the water off and cut the run line square at the tee position.
  • Push the two cut ends onto the straight-through ports of the tee.
  • Then push the branch line onto the side port.
  • Seat each tube fully over its barb so the joint does not pull off under pressure.
  • A slight twist while pushing helps stiff tubing slide on.
  • Warm cold tubing in the sun for a few minutes to soften it.
  • Add up the emitter flow on both sides of the tee to check the feed line can carry it.
  • Very long branches lose pressure toward the end, so keep runs within the dripline maker's length tables.
  • Turn the zone on and check every port for drips at full pressure.
  • Flush both legs with their ends open before closing them off.
  • Mark tee positions on the layout plan so they are easy to find for future repairs.
  • Three Barbed Ports: Splits one 16 mm line into two runs.
  • Push-On Fit: No clamps, glue or tools.
  • Heavy Wall Fit: For 14.2 mm ID dripline, 0.9 to 1.2 mm wall.

Specyfikacje

Fitting Type
Barb tee, barb x barb x barb
Size
16 mm
Dripline Inside Diameter
14.2 mm
Dripline Wall Thickness
0.9 to 1.2 mm
Material
UV and chemical resistant polymer
Pack Quantity
100
Three Barbed Ports
Splits one 16 mm line into two runs.

Sprawmy, żeby to zadziałało w Twoim projekcie

W zapytaniu ofertowym prosimy o podanie ilości, miejsca dostawy, obszaru uprawy oraz wszelkich wymagań dotyczących napięcia lub wtyczki. Specyfikacja, dostępność, warunki wysyłki i gwarancji zostaną potwierdzone w pisemnej ofercie.

Przeliczenie referencyjne przy użyciu zapisanego kursu wymiany z dnia 15 lis 2026. Przeliczone kwoty nie stanowią oferty handlowej.

ROŚNIJMY RAZEM

Pytania i dyskusja

0

Masz pytanie lub chcesz się czymś podzielić? Rozpocznij rozmowę.

KONTYNUUJ ODKRYWANIE

Więcej możliwości dla Twojej przestrzeni

Zobacz wszystkie produkty
POCZĄTEK CZEGOŚ DOBREGO

Rzućmy światło na Twój projekt.

Powiedz nam trochę o swoich potrzebach. Wykorzystamy Twoje dane, aby przygotować odpowiednią odpowiedź hurtową.

Twoja lista produktów

Bez opłat. Bez zobowiązań. Tylko pomocna rozmowa.