Een slimmere manier om te groeien. Rechtstreekse groothandel vanuit de fabriek. Meer dan 15 jaar groeiende expertise

Deze inhoud is momenteel beschikbaar in de oorspronkelijke taal.

ThunderVak Replacement Blades

Model / SKU: 777877

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Type
Replacement cutting wires
Material
Nylon
ReferentieprijsEUR 7.84

Ter vergelijking. Vraag naar de actuele groothandelsprijs, beschikbaarheid en leveringsvoorwaarden.

Geen betaling vereist. Een gesprek over uw behoeften.

Fabrieksdirecte ondersteuningMeer dan 15 jaar ervaring
EEN NADERE KIJK

Nog wat meer informatie over dit product.

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Product details

  • The ThunderVak trims with spinning nylon cords rather than steel knives, and these are the cords it uses.
  • Each wire is a length of round blue nylon with a crimped metal grommet on one end.
  • The grommet seats in the cutting spool on top of the base motor, so the wire stays put at full speed.
  • Fanned out around the spool, the wires sweep just under the aluminum grill.
  • Leaf that hangs through the grill gets clipped while the flower rides above it.
  • The machine runs 8 cutting wires at a time.
  • Nylon cuts cleanly without needing to be sharpened, and a worn wire is swapped for a fresh one.
  • Round blue wires are one of the two styles the trimmer accepts, alongside the octagonal red set.
  • Growers keep a spare set on the shelf so a nicked or shortened cord never stops a harvest.
  • The wires fit the ThunderVak Composter Plus leaf trimmer.
  • As a wear part, a fresh set is the quickest fix for an uneven cut.
  • Swapping Nylon Cutting Wires Between Batches
  • Turn both motors off and unplug the trimmer before touching the cutting area.
  • Lift off the upper reservoir and the grill to expose the spool.
  • Look over every wire for frayed ends, flat spots or missing length.
  • Slide a damaged wire out of its hole in the spool and throw it away.
  • Push a new wire in until its metal grommet seats firmly.
  • Repeat around the spool so the full set is fresh and even.
  • Matching lengths keep the cut level and the motor running smoothly.
  • Set the grill back on and make sure it sits flat on the motor support.
  • The trimming height is preset at the factory, so no adjustment is usually needed after a swap.
  • Run a small handful of material first to confirm the finish looks right.
  • Clean the cutting area after each session with a mild natural cleaner and a damp cloth.
  • Skip abrasive pads, which scratch the surfaces around the spool.
  • Store spare wires flat in a dry bag so they stay straight.
  • Checking the set before every run keeps the trim consistent from first batch to last.
  • Nylon Cutting Cord: Round blue nylon trims leaf cleanly and never needs sharpening.
  • Metal Grommet End: A crimped fitting locks each wire into the cutting spool at speed.

Specificaties

Type
Replacement cutting wires
Material
Nylon

Laten we ervoor zorgen dat het lukt voor jouw project.

Vermeld in uw aanvraag de gewenste hoeveelheid, de bezorgbestemming, het teeltgebied en eventuele spannings- of stekkervereisten. Specificaties, beschikbaarheid, verzending en garantievoorwaarden worden bevestigd in uw schriftelijke offerte.

Referentieconversie met behulp van de opgeslagen wisselkoers van datum 15 nov. 2026. De omgerekende bedragen zijn geen offerte.

Laten we samen groeien.

Vragen en discussie

0

Heb je een vraag of iets nuttigs te delen? Start het gesprek.

BLIJF ONTDEKKEN

Meer mogelijkheden voor uw ruimte

Bekijk alle producten
HET BEGIN VAN IETS GOEDS

Laten we uw project tot leven brengen.

Vertel ons wat u precies nodig heeft. Wij gebruiken uw gegevens om een ​​passende reactie op uw groothandelsaanbod op te stellen.

Uw productlijst

Geen betaling. Geen verplichtingen. Gewoon een behulpzaam gesprek.