이 콘텐츠는 현재 원어로 제공됩니다.
수경재배 및 관개도매 문의
Netafim 16mm Insert Barb Tee - 100 Pack
모델/SKU: 32500-011330
Laying out drip on a bench or a row bed means splitting lines, and the tee is the fitting that does it.
- Size
- 16 mm
- Fitting Type
- Barb tee, barb x barb x barb
- Dripline Inside Diameter
- 14.2 mm
- Dripline Wall Thickness
- 0.9 to 1.2 mm
출처 참조 가격KRW 99,483
비교 목적으로만 사용하십시오. 현재 도매 가격, 재고 여부 및 배송 조건을 문의하십시오.
결제는 필요하지 않습니다. 필요한 사항에 대해 이야기 나눠보세요.
공장 직송 지원15년 이상의 경력
자세히 살펴보기
이 제품에 대해 좀 더 자세히 알아보겠습니다.
Laying out drip on a bench or a row bed means splitting lines, and the tee is the fitting that does it.
Product details
- Netafim 16mm Insert Barb Tee
- This one has three barbed ports in a T shape, all sized for 16 mm dripline.
- Water coming in one side carries straight through and also turns out the branch.
- That lets one feed line serve two beds, or a lateral start partway along a header.
- Netafim lists this tee for 16 mm dripline with an inside diameter of 14.2 mm.
- Its catalog fits it to heavy wall tubing with walls from 0.9 to 1.2 mm.
- Each barb grips the inside of the tube, so no clamps or glue are needed.
- The body is a UV and chemical resistant polymer that holds up to sun and fertilizer in the water.
- It is a single molded piece, so there are no joints inside the fitting to leak.
- Netafim's catalog number for this 100 bag is 32500-011330.
- One bag covers a large layout with tees to spare.
- Keeping spares on hand also makes it simple to add a bed later.
- Branching 16mm Dripline Without Leaks
- Plan the layout first so each tee lands where a branch is needed.
- Turn the water off and cut the run line square at the tee position.
- Push the two cut ends onto the straight-through ports of the tee.
- Then push the branch line onto the side port.
- Seat each tube fully over its barb so the joint does not pull off under pressure.
- A slight twist while pushing helps stiff tubing slide on.
- Warm cold tubing in the sun for a few minutes to soften it.
- Add up the emitter flow on both sides of the tee to check the feed line can carry it.
- Very long branches lose pressure toward the end, so keep runs within the dripline maker's length tables.
- Turn the zone on and check every port for drips at full pressure.
- Flush both legs with their ends open before closing them off.
- Mark tee positions on the layout plan so they are easy to find for future repairs.
- Three Barbed Ports: Splits one 16 mm line into two runs.
- Push-On Fit: No clamps, glue or tools.
- Heavy Wall Fit: For 14.2 mm ID dripline, 0.9 to 1.2 mm wall.
명세서
- Fitting Type
- Barb tee, barb x barb x barb
- Size
- 16 mm
- Dripline Inside Diameter
- 14.2 mm
- Dripline Wall Thickness
- 0.9 to 1.2 mm
- Material
- UV and chemical resistant polymer
- Pack Quantity
- 100
- Three Barbed Ports
- Splits one 16 mm line into two runs.
프로젝트에 도움이 되도록 만들어 봅시다.
문의 시 수량, 배송지, 재배 지역, 전압 또는 플러그 요구 사항을 포함해 주십시오. 사양, 재고 여부, 배송 및 보증 조건은 서면 견적서에서 확인하실 수 있습니다.
저장된 환율을 사용한 참조 변환 (날짜 기준) 2026. 11. 15.. 환산된 금액은 견적이 아닙니다.
계속 탐험하세요
모든 제품 보기
질문 및 토론
궁금한 점이 있거나 유용한 정보를 공유하고 싶으신가요? 대화를 시작해 보세요.