より明るい成長の道。工場直送卸売。 15年以上にわたる専門知識の蓄積

このコンテンツは現在、元の言語で提供されています。

繁殖と植物の手入れ卸売に関するお問い合わせ

ThunderVak Replacement Blades

モデル/SKU: 777877

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Type
Replacement cutting wires
Material
Nylon
出典参考価格JPY 1,382

参考情報としてのみご利用ください。現在の卸売価格、在庫状況、配送条件についてはお問い合わせください。

料金は一切不要です。お客様のニーズについてお話ししましょう。

工場直送サポート15年以上の経験
さらに詳しく見てみよう

この製品についてもう少し詳しく

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Product details

  • The ThunderVak trims with spinning nylon cords rather than steel knives, and these are the cords it uses.
  • Each wire is a length of round blue nylon with a crimped metal grommet on one end.
  • The grommet seats in the cutting spool on top of the base motor, so the wire stays put at full speed.
  • Fanned out around the spool, the wires sweep just under the aluminum grill.
  • Leaf that hangs through the grill gets clipped while the flower rides above it.
  • The machine runs 8 cutting wires at a time.
  • Nylon cuts cleanly without needing to be sharpened, and a worn wire is swapped for a fresh one.
  • Round blue wires are one of the two styles the trimmer accepts, alongside the octagonal red set.
  • Growers keep a spare set on the shelf so a nicked or shortened cord never stops a harvest.
  • The wires fit the ThunderVak Composter Plus leaf trimmer.
  • As a wear part, a fresh set is the quickest fix for an uneven cut.
  • Swapping Nylon Cutting Wires Between Batches
  • Turn both motors off and unplug the trimmer before touching the cutting area.
  • Lift off the upper reservoir and the grill to expose the spool.
  • Look over every wire for frayed ends, flat spots or missing length.
  • Slide a damaged wire out of its hole in the spool and throw it away.
  • Push a new wire in until its metal grommet seats firmly.
  • Repeat around the spool so the full set is fresh and even.
  • Matching lengths keep the cut level and the motor running smoothly.
  • Set the grill back on and make sure it sits flat on the motor support.
  • The trimming height is preset at the factory, so no adjustment is usually needed after a swap.
  • Run a small handful of material first to confirm the finish looks right.
  • Clean the cutting area after each session with a mild natural cleaner and a damp cloth.
  • Skip abrasive pads, which scratch the surfaces around the spool.
  • Store spare wires flat in a dry bag so they stay straight.
  • Checking the set before every run keeps the trim consistent from first batch to last.
  • Nylon Cutting Cord: Round blue nylon trims leaf cleanly and never needs sharpening.
  • Metal Grommet End: A crimped fitting locks each wire into the cutting spool at speed.

仕様

Type
Replacement cutting wires
Material
Nylon

あなたのプロジェクトに役立てましょう

お問い合わせの際は、数量、配送先、栽培地域、電圧やプラグに関するご要望を明記してください。仕様、在庫状況、配送条件、保証条件は、書面による見積書にてご確認いただけます。

保存された為替レートを使用した参照換算 2026/11/15. 換算された金額は見積もりではありません。

一緒に成長しよう

質問とディスカッション

0

質問や役立つ情報があれば、ぜひ共有してください。会話を始めましょう。

探検を続けよう

空間の可能性がさらに広がります

すべての商品を見る
良いことの始まり

あなたのプロジェクトを世に知らしめましょう。

お客様のご要望について少しお聞かせください。いただいた情報をもとに、適切な卸売りのご提案をさせていただきます。

商品リスト

料金は一切かかりません。義務も一切ありません。ただ、有益な会話を楽しみたいだけです。