Ce contenu est actuellement disponible dans sa langue d'origine.
Titan Controls CO2 Regulator
Modèle / UGS: 702710
Titan Controls CO2 Regulator for Tank-Fed Grow Rooms
- Flow Range
- 0.5-15 SCFH
- Compatible Controls
- Any 120 volt CO2 controller or timer
- Tank Pressure Gauge
- Shows how much CO2 is left in the cylinder.
- Controller Compatible
- Atlas CO2 controllers, Apollo timers and wall timers.
À titre indicatif seulement. Veuillez nous contacter pour connaître nos tarifs de gros actuels, la disponibilité des produits et les conditions de livraison.
Aucun paiement requis. Une simple discussion pour comprendre vos besoins.
Un peu plus d'informations sur ce produit
Titan Controls CO2 Regulator for Tank-Fed Grow Rooms
Product details
- Enriching a sealed room with bottled CO2 starts at the tank, and this regulator is the piece that meters the gas out.
- Titan Controls item 702710 combines a tank pressure gauge, a flowmeter and a heavy-duty 120 volt solenoid in one body.
- The flowmeter reads from 0.5 to 15 standard cubic feet per hour, set with a brass flow adjustment knob.
- A ball rises and falls inside the clear tube, so the flow rate is visible at a glance.
- The solenoid opens only when it receives power, which lets a controller or timer decide when CO2 flows.
- That makes it compatible with any 120 volt CO2 controller or timer, including Titan's Atlas monitor/controllers and Apollo repeat cycle timers.
- With an Atlas controller, gas runs whenever the room drops below the PPM set point.
- With a timer, the regulator opens at set intervals based on room volume and flow rate.
- Titan's instructions include a timing chart for raising a room by about 1,100 to 1,200 PPM, to roughly 1,500 PPM total.
- For rooms over 2,000 cubic feet, the sheet gives a simple formula for working out run time.
- Installing a CO2 Regulator With Solenoid on the Tank
- Before connecting, crack the tank valve open for about 3 seconds to blow out any debris, then close it.
- Seat one of the white plastic washers inside the large brass nut to prevent leaks.
- Tighten the nut with a crescent wrench, not pliers, and do not hold the plastic flowmeter while tightening.
- Skip pipe thread tape and lubricants on the tank connection.
- Run the 1/4 in tubing from the barbed fitting to the back of an oscillating fan, which helps spread CO2 around the room.
- Open the flow knob about half a turn before opening the tank, then open the tank valve 2 or 3 turns.
- Check every connection with soapy water for leaks.
- Set the flow with the brass knob.
- Never open it so far that the ball passes the top of the scale, since that can freeze the regulator.
- Run CO2 only while the lights are on, and keep room levels below 2,500 PPM.
- Titan covers the regulator against material defects for 1 year, and replacement washers are item 702712.
- 0.5-15 SCFH Flowmeter: Visible ball indicator with a brass adjustment knob.
- 120V Solenoid: Opens only when the controller or timer powers it.
- Tank Pressure Gauge: Shows how much CO2 is left in the cylinder.
- Controller Compatible: Atlas CO2 controllers, Apollo timers and wall timers.
- Timing Chart Included: Run times by room volume and flow setting.
- Technical Specifications
Caractéristiques
- Flow Range
- 0.5-15 SCFH
- Compatible Controls
- Any 120 volt CO2 controller or timer
- Tank Pressure Gauge
- Shows how much CO2 is left in the cylinder.
- Controller Compatible
- Atlas CO2 controllers, Apollo timers and wall timers.
Faisons en sorte que cela fonctionne pour votre projet.
Veuillez indiquer la quantité, le lieu de livraison, la zone de culture et toute exigence en matière de tension ou de prise dans votre demande. Les spécifications, la disponibilité, les modalités d'expédition et de garantie seront confirmées dans votre devis écrit.
Conversion de référence utilisant le taux de change enregistré à la date 15 nov. 2026. Les montants convertis ne constituent pas une cotation.
Plus de possibilités pour votre espace
Yield Lab 6 Inch Purifier Activated Charcoal Filter
Yield Lab 6 inch 440 CFM Duct Inline Fan with 6" Carbon Filter Ducting and Clamps
Yield Lab 6 Inch 440 CFM Charcoal Filter and Duct Fan Combo Kit
Questions et discussion
Vous avez une question ou quelque chose d'utile à partager ? Lancez la conversation.