Una forma más brillante de crecer. Venta al por mayor directamente de fábrica. Más de 15 años de experiencia en constante crecimiento.

Este contenido está disponible actualmente en su idioma original.

ThunderVak Replacement Blades

Modelo / SKU: 777877

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Type
Replacement cutting wires
Material
Nylon
Precio de referencia de la fuenteEUR 7.84

Solo a título informativo. Solicite su precio mayorista actual, disponibilidad y condiciones de entrega.

No se requiere ningún pago. Una conversación sobre lo que necesitas.

Soporte directo de fábricaMás de 15 años de experiencia
UNA MIRADA MÁS DETALLADA

Un poco más sobre este producto

ThunderVak Replacement Blades for the Composter Plus Leaf Trimmer

Product details

  • The ThunderVak trims with spinning nylon cords rather than steel knives, and these are the cords it uses.
  • Each wire is a length of round blue nylon with a crimped metal grommet on one end.
  • The grommet seats in the cutting spool on top of the base motor, so the wire stays put at full speed.
  • Fanned out around the spool, the wires sweep just under the aluminum grill.
  • Leaf that hangs through the grill gets clipped while the flower rides above it.
  • The machine runs 8 cutting wires at a time.
  • Nylon cuts cleanly without needing to be sharpened, and a worn wire is swapped for a fresh one.
  • Round blue wires are one of the two styles the trimmer accepts, alongside the octagonal red set.
  • Growers keep a spare set on the shelf so a nicked or shortened cord never stops a harvest.
  • The wires fit the ThunderVak Composter Plus leaf trimmer.
  • As a wear part, a fresh set is the quickest fix for an uneven cut.
  • Swapping Nylon Cutting Wires Between Batches
  • Turn both motors off and unplug the trimmer before touching the cutting area.
  • Lift off the upper reservoir and the grill to expose the spool.
  • Look over every wire for frayed ends, flat spots or missing length.
  • Slide a damaged wire out of its hole in the spool and throw it away.
  • Push a new wire in until its metal grommet seats firmly.
  • Repeat around the spool so the full set is fresh and even.
  • Matching lengths keep the cut level and the motor running smoothly.
  • Set the grill back on and make sure it sits flat on the motor support.
  • The trimming height is preset at the factory, so no adjustment is usually needed after a swap.
  • Run a small handful of material first to confirm the finish looks right.
  • Clean the cutting area after each session with a mild natural cleaner and a damp cloth.
  • Skip abrasive pads, which scratch the surfaces around the spool.
  • Store spare wires flat in a dry bag so they stay straight.
  • Checking the set before every run keeps the trim consistent from first batch to last.
  • Nylon Cutting Cord: Round blue nylon trims leaf cleanly and never needs sharpening.
  • Metal Grommet End: A crimped fitting locks each wire into the cutting spool at speed.

Presupuesto

Type
Replacement cutting wires
Material
Nylon

Hagamos que funcione para tu proyecto.

En su consulta, incluya la cantidad, el destino de entrega, la zona de cultivo y cualquier requisito de voltaje o enchufe. Las especificaciones, la disponibilidad, el envío y las condiciones de garantía se confirmarán en su presupuesto por escrito.

Conversión de referencia utilizando el tipo de cambio guardado con fecha 15 nov 2026. Los importes convertidos no constituyen una cotización.

CREZCAMOS JUNTOS

Preguntas y debate

0

¿Tienes alguna pregunta o algo útil que compartir? Inicia la conversación.

SIGUE EXPLORANDO

Más posibilidades para tu espacio

Ver todos los productos
EL COMIENZO DE ALGO BUENO

Vamos a sacar tu proyecto a la luz.

Cuéntenos brevemente qué necesita. Utilizaremos sus datos para preparar una respuesta mayorista adecuada.

Lista de productos

Sin pago. Sin compromiso. Simplemente una conversación útil.