Ein vielversprechenderer Weg zum Wachstum. Großhandel direkt ab Werk. Mehr als 15 Jahre wachsende Expertise

Dieser Inhalt ist derzeit in seiner Originalsprache verfügbar.

Belüftung & KlimaGroßhandelsanfrage

Quest Duct Kit (Q100)

Modell / Artikelnummer: 4042265

Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.

QuellenreferenzpreisEUR 185.73

Nur zum Vergleich. Fordern Sie Ihren aktuellen Großhandelspreis, die Verfügbarkeit und die Lieferbedingungen an.

Keine Zahlung erforderlich. Ein Gespräch über Ihre Bedürfnisse.

Direkter WerkssupportMehr als 15 Jahre Erfahrung
EIN GENAUERER BLICK

Noch ein paar weitere Informationen zu diesem Produkt

Its part number is 4042265, and Quest builds it for the Quest 100 dehumidifier, PN 4041870, and the 50 Hz version, PN 4046590.

Product details

  • What Is in the Quest 100 Duct Kit
  • Each one carries a round collar for duct, so the unit can draw from one space and deliver to another.
  • That is what lets a Quest 100 sit in a lung room, a hallway or a mechanical closet.
  • It still works the grow room through two runs of flex duct.
  • The filter stays in service.
  • The magnetic door closes over it, so a filter change is a pull and a push rather than a plenum removal.
  • Fitting it needs a portable drill, a T25 Torx driver and a 5/16 in hex driver, and nothing else.
  • The plenums hang on the cabinet's own panel screws.
  • Those screws back out halfway, the plenum's keyed slots drop over them, and the screws are tightened again.
  • The four fasteners then anchor the plenum tabs into the plastic base, self-drilling, with no pilot holes.
  • Quest's instructions open with the warning that matters: disconnect the dehumidifier from power before any of it starts.
  • The kit ships at about 5 lb.
  • Keep both runs as short and as straight as the room allows, and size them to the collars rather than necking down.
  • Back the two top panel screws and the two right panel screws out halfway, hang the plenum on them, and tighten.
  • Drive the two fasteners through the bottom tabs into the base.
  • Slide the filter in, arrow toward the machine, and close the magnetic door with the larger tab on top.
  • Then the supply side: four screws out halfway on the top, rear and left panels, plenum on, screws tight, two more fasteners into the base.
  • Seal the duct to each collar with foil tape rather than cloth tape.
  • A dehumidifier discharge is warm, and cloth adhesive lets go within a season.
  • Check the filter monthly once it is ducted.
  • Out of sight behind a door, a filter loads up faster than one on an open cabinet.
  • A loaded filter is the second reason a ducted unit underperforms.
  • Four self-drilling fasteners: Anchor the plenums to the base with no pilot holes.
  • Hangs on the panel screws: Keyed slots over half-backed screws, then tightened.
  • Three tools: Portable drill, T25 Torx driver, 5/16 in hex driver.
  • For the Quest 100: PN 4041870, and the 50 Hz PN 4046590.
  • Quest part 4042265: About 5 lb boxed.
  • Technical Specifications

Lass es uns für dein Projekt zum Laufen bringen

Bitte geben Sie in Ihrer Anfrage die gewünschte Menge, den Lieferort, die Anbaufläche sowie eventuelle Spannungs- oder Steckeranforderungen an. Spezifikationen, Verfügbarkeit, Versand- und Garantiebedingungen werden in Ihrem schriftlichen Angebot bestätigt.

Referenzumrechnung unter Verwendung des gespeicherten Wechselkurses vom 15.11.2026. Die umgerechneten Beträge stellen kein Angebot dar.

LASST UNS GEMEINSAM WACHSEN

Fragen und Diskussion

0

Haben Sie eine Frage oder möchten Sie etwas Nützliches teilen? Starten Sie das Gespräch.

WEITER ERKUNDEN

Mehr Möglichkeiten für Ihren Raum

Alle Produkte ansehen
DER BEGINN VON ETWAS GUTEM

Lass uns dein Projekt ans Licht bringen.

Schildern Sie uns kurz Ihre Anforderungen. Wir nutzen Ihre Angaben, um Ihnen ein passendes Angebot für den Großhandel zu unterbreiten.

Ihre Produktliste

Keine Zahlung. Keine Verpflichtung. Nur ein hilfreiches Gespräch.