Providing detailed information on the Grow Genius System.
Both the GGS Controller and GGS Power Strip are master control devices that can operate independently, directly managing sensors and connected devices (heaters, humidifiers, dehumidifiers, lights, etc.).
When used together, the Controller becomes the top-level master and the Power Strip becomes a mid-tier device — managed by the Controller above, while still managing its own connected devices and sensors below.
The hierarchy is: Controller (top master) → Power Strip (mid-tier) → Sub-devices + Sensors
The GGS ecosystem includes four main categories of devices:
Controllers & Hubs — GGS Pro Controller, GGS Controller, GGS Power Strip, S Station
Sensors — Standard sensor, 4-in-1 / 5-in-1 Sensor Pro Kits, Soil Sensor
Smart Add-ons — SF-IRAC (smart Air Conditioner Companion)
GGS is a flexible ecosystem. There are two ways to get started:
Option A — Full Automation (System Level) To automatically control dehumidifiers, heaters, fans based on temperature and humidity, you need:
One master control device (GGS Controller, GGS Power Strip, or S Station)
At least one sensor (included with Controller / Power Strip kits)
Option B — Smart Light Control Only If you have SE or G series LED grow lights, they can be added directly to the APP without any controller.
Place the sensor at canopy level for the most accurate readings. Avoid placing it:
Directly under the grow light or in direct light (inflated temperature)
Near intake or exhaust fans (airflow affects readings)
On the tent wall, floor, or top corners (not representative of canopy conditions)
Most users complete the full setup in 15–20 minutes:
Install and connect all devices (controller, sensors, sub-devices, etc.) (~5 min)
Power on the controller and pair with the APP via Bluetooth (~3 min)
Set your target environment parameters (~5 min)
GGS works entirely without a subscription. All core features — real-time monitoring, automation rules, alerts, and data history — are included free with the hardware.
GGS devices only support 2.4GHz WiFi. This is standard for IoT devices because 2.4GHz offers better range and wall penetration.
Confirm your WiFi is 2.4GHz (not 5GHz)
Move the controller closer to your router during initial setup
Check that your WiFi password does not contain special characters
Restart the controller or restore factory settings
Delete the device from the APP and re-add it
After power is restored, GGS devices will automatically reconnect to WiFi as long as the network is working normally — no manual action needed.
If the APP is fully closed (background process terminated), the Bluetooth connection may drop and will restore when you reopen the APP.
The APP will automatically scan for nearby devices via Bluetooth, including:
G series / SE series LED grow lights (with digital dimmer box)
Humidifiers, heaters, and dehumidifiers cannot be found directly via Bluetooth, but once connected to a master control device they can be recognized and controlled in the APP.
When Bluetooth is available, the app will prioritize Bluetooth for communication as it is faster.
VPD (Vapor Pressure Deficit) measures the difference between the moisture in the air and the maximum moisture the air can hold. It's the most accurate way to understand how your plants "feel" their environment.
GGS calculates VPD automatically from temperature and humidity readings.
You can view daily, weekly, and monthly trend charts directly in the APP.
Data can be exported as CSV through the APP's settings menu for further analysis.
Each master control device (GGS Controller, GGS Power Strip, S Station) supports only one sensor per type — except soil sensors, which support up to 6. If you need to monitor multiple grow spaces, the GGS Pro Controller supports up to 8 independent rooms, each with its own sensor.
First, check sensor placement — proximity to lights or fans is the most common cause of inaccurate readings.
To calibrate: open the APP → Sensor Calibration; use a known-accurate thermometer/hygrometer as reference; enter offset values to adjust readings.
Dashes (--) indicate the controller cannot communicate with the sensor. Common causes:
Sensor is not connected or plug is not fully seated
Incorrect wiring order or wrong port between master device and sensor
Try: re-seating the sensor cable firmly; checking that all wiring connections are correct; replacing the sensor cable if damaged.
Both controllers manage inline fans, lights, and sensors. Key differences:
Hardware: Pro has a touchscreen and is designed for multi-room / large-scale setups; standard is more compact, ideal for single-tent use.
Deep integration: Both support precise % dimming/speed control and scheduling for LED lights and inline fans.
Pro Controller (current limitation): The GGS Pro Controller supports multiple Temperature & Humidity Sensors for independent multi-zone monitoring, making it ideal for commercial cultivation. The standard GGS Controller supports only one Temperature & Humidity Sensor. Since both the Temperature & Humidity Sensor and the 5-in-1 Sensor measure temperature and humidity, only one of these sensors can be connected at a time.
Standard Controller & Power Strip: Already adapted for retail peripherals with full mode and parameter control in the APP.
GGS supports two automation modes for each device. Below is an overview by device type:
① Time Mode: Multi-segment timing (set start/end times + fan speed + standby speed; CO₂ device power is automatically cut while fan runs) or Cycle timing (run duration → pause duration → repeat).
② Environment Mode: 5 trigger options based on real-time sensor data — Temp Only, Humidity Only, Temp & Humidity, Temp Priority (force-stop if temp too low), Humidity Priority (force-stop if humidity too low).
Humidifier — Time segment / Cycle / Humidity mode (4 levels + auto level)
Dehumidifier — Time segment / Cycle / Humidity mode (2 speed levels)
SF-IRAC (AC companion) — Time segment / Cycle / Environment mode (temperature-based)
LED Grow Light — Scheduled dimming with sunrise/sunset simulation; PPFD mode (requires Sensor Pro Kits)
Power Strip outlets — Multi-segment timer, cycle timer, heating mode, cooling mode, humidification mode, dehumidification mode, CO₂ boost, CO₂ exhaust, drip irrigation (soil sensor moisture-based)
The controller supports scheduled dimming, sunrise/sunset simulation, and stage-based light programs.
If an update is available, tap "Update Now". Keep the controller powered on during the update. Do not unplug during a firmware update — this may cause the device to become unresponsive.
GGS uses a one-to-one account binding — one device can only be controlled by one account. If another phone logs into the same account, the original device will be automatically signed out, but device settings are preserved.
Via Controller: Use "User Reset" to unbind the account. The new account can then search for and add the device. Do not use "Reset" (Factory Reset) — this erases all settings.
Via APP: Swipe left to delete the device in the APP, then the new account can search for and add it.
There is no web dashboard or desktop application available at this time.
When a value exceeds your set range, an in-app alert is triggered.
Note: Push notifications are currently in development. In-app alerts are available now.
Check if an update is available in the App Store or Google Play
Check that your WiFi router is working normally
Unplug the controller, wait a moment, then plug it back in
Check if the controller's WiFi indicator light is on
If the above steps don't work, delete the device from the APP and re-add it
Confirm the automation rule is enabled (toggle is on)
Check that the sensor is connected and showing live readings
Verify the trigger conditions — the current environment may already be within the target range, so the rule has not triggered yet
Confirm the fan is properly connected to the controller
Try manually controlling the fan from the APP to confirm the device responds
Push notification support is currently in development. In-app alerts are available now — you can set thresholds for temperature, humidity, VPD, CO₂, PPFD, and soil parameters in the APP.
GGS Controller: Go to Settings → "Factory Data Reset"
GGS Power Strip: Long-press the Ctrl button until the indicator light flashes
G / SE series lights (with digital dimmer box): Long-press the knob
Warning: A factory reset erases all automation rules, schedules, and settings and cannot be undone.
LED Grow Lights: SE series, SF series, G series
Environmental controls: SF humidifiers, dehumidifiers, heaters
Sensors: GGS Standard Day/Light sensor, 4-in-1 Sensor Pro Kits, 5-in-1 Sensor Pro Kits, Soil Sensor
Note: some older models may not be compatible. Always check the product page description carefully before purchasing.
It does not integrate with third-party controllers, sensors, or smart home platforms such as Inkbird or Govee.
You can use GGS alongside other systems independently — they just won't communicate with each other.
GGS does not currently support integration with Amazon Alexa, Google Home, Apple HomeKit, or other smart home platforms.
You can add multiple master control devices (GGS Controller, GGS Power Strip, or S Station) to the same APP account — each independently manages its own grow space with one sensor.
For single-device multi-zone management, the GGS Pro Controller supports up to 8 independent rooms, each with its own sensor, all visible in one APP dashboard.
Can't find the answer you're looking for?
Drag the sliders to simulate current temp & humidity and observe fan trigger logic.
Questions & discussion
Have a question or something useful to share? Start the conversation.